Post Offer Free
OAS Factory Auto Electrics Co.,Ltd  

Gold Index: 5478

You are here: home  > Professional Diagnostic Tools   > 883S CLONER

883S CLONER 

Place of Origin: , China (Mainland) 
inquire
Add to My Favorites
HiSupplier Escrow
Share |

Product Detail


High-tech products and specialized service would give you a refreshing appearance.

With the 883S Cloner key cutting machine, the messages shown in the table below will appear on the display depending on the different transponder types of the key you wish to cut.
     JMA REF.  TRS-5000 RESULT  ACTUAL TRANSPONDER  
TP01  TP01 Philips Fixed Copy on TP05  PHILIPS basic original 
TP02  TP02 TEXAS Fixed Copy on TPX1  TEXAS Fixed Crystal 23 mm = TP07 
TP03  TP03 MEGAM Fixed Copy on TP05  MEGAMOS Fixed Crystal 13 mm 
TP04  TP04 TEMIC Fixed Copy on TP05  TEMIC fixed wedge format plastic 
TP05  TP05 NOVA Fixed Copy on TP05  NOVA (Universal transponder for fixed keys)  
TP06  TP06/19 TexCrypt See TP manual  TEXAS Crypto Crystal 23 mm 
TP07  TP02 TEXAS Fixed Copy on TPX1  TEXAS Fixed plastic wedge = TP02 
TP08  TP08 MEGAM Crypt See TP manual  MEGAMOS Crypto Crystal 13 mm 
TP09  TP09 Phil Cry OP See TP manual  Philips Crypto 1st generation OPEL load 
TP10  TP10 Phil Cry WS See TP manual  Philips Crypto 1st generation VW load, low range 
TP11  TP08 Megam Crypt See TP manual  MEGAMOS Crypto plastic wedge = TP08 
TP12  TP12 Phil Crypto See TP manual  Philips Crypt CITROEN-PEUGEOT (2000 =>..) 
TP13  TP13 Phil Cry NS See TP manual  Philips Crypto 1st generation NISSAN load 
TP14  TP14 Phil Cry WS See TP manual  Philips Crypto 2nd generation VW load low range 
TP15  TP09 Phil Cry OP See TP manual  Philips Crypto 2nd generation OPEL load = TP09 
TP16  TP16 Phil Cry PG See TP manual  Philips Crypto 1st generation PEUGEOT load 
TP17  TP17 TEMIC Crypt See TP manual  TEMIC Crypto (Mazda vehicles) 
TP18  TP18 MOTOROLA Indala  Motorola Indala (Lincoln MARK VIII) 
TP19  TP06/19 TexCrypt See TP manual  TEXAS Crypto plastic wedge = TP06 
TP20  TP20 Tex Cr FORD See TP manual  TEXAS Crypto plastic wedge = Special for FORD W1
TP21  TP21 TexCryp REN See TP manual  TEXAS Crypto plastic wedge = Special for RENAULT, JEEP, CHRYSLER 
TP22  TP08 Megam Crypt See TP manual  Megamos Crypto Special for SEAT 2005 
TP23  TP08 Megam Crypt See TP manual  Megamos Crypto Special for VW 2005 
TP24  TP08 Megam Crypt See TP manual  Megamos Crypto Special for SKODA 2005 
TP25  TP08 Megam Crypt See TP manual  Megamos Crypto Special for AUDI 2005 
TP26  TP26 TexCryp MIT See TP manual  TEXAS Crypto plastic wedge = Special MITSUBISHI  

The procedure for copying keys is as follows:
              1 Local mode, without connection to PC
            - Insert the customer's original or sample key in the antenna housing and press the READ key. A message will appear on the display with the type and JMA reference of the original key's transponder, together with the type of transponder JMA recommends copying onto. This is valid for fixed code transponders. If the transponders are encrypted, the system will identify the transponder and its JMA reference and will indicate the procedure for activating the key, which is normally using our transponder manual.
            - Then follow the procedure indicated by the machine. Take out the key and insert the new key to be cut, together with its corresponding transponder. An uncut (non-machined) key should be inserted for cutting, as any swarf or burr adhered to the key could damage the machine antenna. Also make sure no swarf or metal particles fall into the antenna or circuits of the TRS-5000, as this could cause interference and the key will not be copied correctly.
            - When the key has been cut, the machine will indicate whether a correct copy has been made or not.
            - If you wish to make more than one copy of the same key, repeat the above steps, remember you should make the copy from the original key provided by the customer, and the "base for copying" should be the transponder with the reference recommended by JMA.
          2 Connected to a Computer (Connected to PC Mode)
As we have mentioned previously, a CD is included with the unit containing an interface program for making copies of keys from the computer. The software installation procedure is described on the following page.
This PC or interface software offers the following advantages:
            - The customer’s data can be stored for making subsequent copies (you will have a database of customers who have cut their keys in your establishment).
            - Attractive, easy-to-use Windows interface, compatible with all OS versions.
            - You can choose the language you wish to work in.
            - More than one key can be cut without needing to repeat the reading process.
            - Fixed code transponder pre-loading can be done with a certain code, which can be adapted to your needs.
bigPhoto
 Ms. june

Tel: 86-755-21506221
Contact to this supplier

Related Search

Find more related products in following catalogs on Hisupplier.com

Company Info

OAS Factory Auto Electrics Co.,Ltd [China (Mainland)]


Business Type:Manufacturer
Country/Region: China (Mainland)

You May Like: